top of page
Search

Tips and Tricks for Using Our New Lei Stamps

5 days ago
4 min read

Hi There! I wanted to take some time to give you a few pointers on using our new lei stamps. It took me a little while to get the hang of using these stamps, so be prepared to practice a bit on some scrap paper. If you don't, you may end up ruining some projects like I did :/



The first style is the easiest...stamping single strands of lei. I mounted each of the 4 lei flower stamps close to the bottom edge of the wood mount so that you can easily stamp each flower right up against the last flower in the strand. I start by drawing a light line in pencil where I want my lei to go (to be erased later). Then I use that line as a guide (it doesn't have to be exactly along the line, but it should follow in the general direction you want to go). Aim the top of your flower stamp toward that pencil line and match the bottom edge to the top edge of the previous flower (See green arrow in photo below). A little bit of overlap is the best, but it doesn't have to be perfect to turn out nice.



Below is a sample of this first method:




The next examples will require masking. A mask is used to cover a stamped image so that anything stamped on the mask will appear to be underneath the previously stamped image. To make a mask, simply stamp your image on the sticky part of a post it note (so that it will stay in place when you're ready to use it), then cut out the image.


I'll start with the pakalana stamp. In reality each flower is nestled into the previous flower in a lei strand. I'll show you how to mask the stamp so each flower appears that way.



Starting from the top, left corner in the photo above:

  1. Stamp your image on a post it note and cut it out to make your mask. You may want to replace the mask periodically as the ink from the inkpad will start to bleed through the post it note and stain your paper.

  2. Draw a line in pencil where you want your lei to go, then stamp the first flower.

  3. Put the mask on top of the image you just stamped

  4. Stamp the next flower, overlapping the first flower.

  5. Remove the mask and note how the second flower is "under" the first flower, or nestled into the first flower.

  6. Continue putting a mask over the last flower you stamped and stamp the next flower on top of that.

  7. The final photo shows a strand of pakalana. I might also use this method for the puakenikeni (the pikake and rosebud stamps work well with the first method). It just depends on the look you want (and the amount of work you want to put in :)


Next, I'll show you how to do strands that cross one another.



Stamp your first strand in one of the methods described above. This strand will always be the strand on the top. All other strands fall below. To do your second strand, draw a pencil line that intersects the first. Mask all the flowers that will intersect with your second strand. Then stamp your second strand. Once you remove the masks you'll see that the pikake strand is under the pakalana strand. For a third layer, draw a pencil line that intersects the first and second strand. Again, mask all flowers that will intersect. Remove the masks and you'll see that the rose strand is below the pikake and pakalana strands.


A side note...you won't need as many masks as I've shown in the photo. That was just to give you a clear picture of the area that needs to be masked. When you are actually stamping, you can move the mask as you go. But, please, make sure to mask everything that could possibly be affected. I've ruined a few attempts by thinking I wouldn't overlap something, but I did. Always better to be safe :)


The next method is a twisted lei. I'm still practicing to get this down really well.



Start with a pencil line of the general shape that you want your lei to be. Next, draw another squiggly line along the first line, never going farther from the original line than the width of the flower image you are using.


What you have to keep in mind is that you will be alternating the strand that is on top. I'll start with the pakalana strand along the squiggly line. Stamp a few blossoms until you're around the peak point of the squiggly line. Next, mask all the blossoms you've just stamped.


For the next strand, the pikake strand, I didn't draw a second squiggly line because I think it's easier to work off of the pakalana strand. As you're stamping over the mask, keep the pikake close to the pakalana so that it's slightly overlapping. Continue the pikake strand to the top of the next "imaginary" peak (continuing a curvy path and not straying too far from the original line). Continue masking and stamping in this way to get your twisted lei.


Now you can add a lei onto anything you can stamp on. I hope the instructions are clear (They make sense in my head...lol!) If you have any questions, please leave them in the comment section below.


 
 
 

Comments


bottom of page